Cached at:
11/16/26, 02:13 PM
# OOS - an open operating system for the Rigol Scopes
Source: [https://www.eevblog.com/forum/testgear/oos-an-open-operating-system-for-the-rigol-scopes](https://www.eevblog.com/forum/testgear/oos-an-open-operating-system-for-the-rigol-scopes)
**OOS: an open operating system for the Rigol DHO800/DHO900**
OOS replaces the software of a Rigol Scope \(right now Supported DHO800/DHO900\) with a**Linux 6\.12 kernel**and a**new scope application written in Rust**\. It runs from the scope's own SD card,**next to the stock system**, and you can switch back at any time\. Source, releases and guides:[github\.com/deckerjulian/oos](https://github.com/deckerjulian/oos)\(GPL\)\.
All pictures are screenshots of a DHO924S running OOS\.
---
**Experimental software\.**So far OOS has run on**one DHO924S**only, and some functions have never run on real hardware\. Measurements made with OOS are not calibrated to any standard\. You use it at your own risk; please read the[disclaimer](https://github.com/deckerjulian/oos#disclaimer)before you install it\.
What OOS never touches: the FPGA flash, the factory calibration in
/rigol/data, and the
uboot,
trustand
parameterpartitions\. Its own self\-calibration goes into its own files\.
---
**What is in it**
**Acquisition and trigger**
- Normal, peak detect, average, high resolution; memory depth up to 125 M points; 1 ns/div up to roll and scan mode
- Hardware trigger: edge, pulse, slope, video, pattern, duration, timeout, runt, window, delay, setup/hold, Nth edge
- Protocol trigger on decoded bus events, zone trigger with boxes or polygons
**Measurement and maths**
- 35 automatic measurements with statistics, delay and phase, cursors, DVM and counter
- A second pane under the plot: spectrum with peak list, results table, decoder events, or trends of two measurements
- 8 math channels with free formulas \(sqrt\(CH1^2\+CH2^2\)\), filters, FFT; reference waveforms, mask test, CSV data logger
**Protocol decoders \(25\)** UART, I2C, SPI, Quad\-SPI, I3C, 1\-Wire, SWD, JTAG, CAN, CAN\-FD, LIN, FlexRay, SENT, ARINC 429, MIL\-STD\-1553, I2S, S/PDIF, DMX512, Modbus, USB LS/FS, USB PD, parallel and more; four at once, with an event table\.
**Analysers**
- Spectrum analyser with harmonics, THD, SNR, SFDR, waterfall
- Eye diagram and jitter \(TJ/RJ/DJ, DCD, DDJ, PJ\), power analysis, Bode plot with the built\-in or an external generator
- Bandwidth test from a fast edge\. OOS does not limit the bandwidth to the rated value
**Logic analyser**\(PLA2216, DHO900\),**generator**\(S models: sine, square, ramp, pulse, noise, DC, arbitrary, AM/FM/PM\),**HDMI**as mirror or second workspace\.
**Remote control**over Ethernet or a WLAN stick: SCPI on port 5555 \(Rigol\-style subset,
:WAV:MODE RAWreads every sample\), VXI\-11, a web remote with live screen and touch on port 8080, LXI identification, MCP for AI assistants, and telnet \(a root shell without password: keep the scope on a network you trust\)\.
**System**: its own cold boot of the hardware \(stock never has to run first\), self\-calibration, signed updates with trial start and automatic rollback, experimental overclocking of the sample clock\.
---
**Models**
OOS reads the model from the unit and adapts channels, logic analyser, generator and EXT trigger to it\.
**Model****Channels****LA****Generator****Run OOS?**DHO802 / DHO8122\-\-not yetDHO804 / DHO814 / DHO8244\-\-a DHO804 runs it \(user report\)DHO914 / DHO924 \(also EDU\)4yes\-not yetDHO914S4yesyesnot yetDHO924S4yesyes**yes, the development unit**DHO1000, HDO and MHO are different boards and not supported\.
---
**Installing**
Everything is in the[latest release](https://github.com/deckerjulian/oos/releases/latest); you do not have to build anything\.
- **From a USB stick**, scope closed:DHO800\_DHO900\_OOS\_Install\.GELthrough*Storage \> Upgrade*of the stock system\. Do the dry run first\. So far only accepted on the DHO924S\.
- **On a second SD card**, scope opened: back up the original card, clone it, installoos\-<version\>\.img\. The original card stays in a drawer\. A second card a few MB smaller than the original works too \(tools/sdcard\-clone\.sh fit\)\.
- **Updates**of a running OOS: the\.oosupdfile throughhttp://<scope\>:8080/update\.
Step by step:[wiki: Installation](https://github.com/deckerjulian/oos/wiki/Installation)\. Going back to stock is one power cycle, or putting the original card back:[wiki: Updates and Going Back](https://github.com/deckerjulian/oos/wiki/Updates-and-Going-Back)\.
**Building it yourself**works on macOS \(Apple silicon\) and on Linux, arm64 and x86\-64; on a normal PC the kernel is cross\-compiled in Docker:[wiki: Building](https://github.com/deckerjulian/oos/wiki/Building)\. You can also run the GUI on your computer without a scope, with simulated signals\.
---
**What would help**
- **Reports from other models**than the DHO924S: what works, what does not, the start\-up screen andoos\-fpgad model
- Real signals for the protocol decoders, most were only tested with simulated ones
- Bugs and ideas as[GitHub issues](https://github.com/deckerjulian/oos/issues), or here in this thread
---
**Thanks**
OOS builds on the work of others\. In particular:[NovaOS](https://github.com/Bradyok/novaos-kernel-source)by Olympian LED, Inc\., for publishing the GPL source of its Linux port to this hardware, which showed what a kernel needs here and where OOS started \(the OOS kernel patches, device tree and configuration are written anew\);[Norbert Kiszka](https://github.com/norbertkiszka)for the modified firmware and the findings he shared in public; Linux and Rockchip, the Xilinx XDMA driver, BusyBox, e2fsprogs, wpa\_supplicant, Rust\. The full list is in the[README](https://github.com/deckerjulian/oos#thanks)\.
**Links**
- Repository:[github\.com/deckerjulian/oos](https://github.com/deckerjulian/oos)
- Releases:[latest release](https://github.com/deckerjulian/oos/releases/latest)
- Wiki:[guides](https://github.com/deckerjulian/oos/wiki)
- How the hardware works:[hardware overview](https://deckerjulian.github.io/oos/hardware/overview.html)